Wall seepage and floor cracks let moisture invade your home year-round. Our certified team in Chester delivers lasting waterproofing that holds.
Four reasons why Chester homeowners trust us with their most important asset.
Our interior drain tile systems are sized and sloped to specification, ensuring gravity carries water to your sump pump without clogging or backing up over time.
Porous concrete block and poured walls let groundwater seep through at the mortar joints -- we seal them from the inside with hydraulic cement and crystalline coatings that bond permanently.
We document every installation with before-and-after photos, moisture readings, and a written record so you have evidence of the work performed and its conditions.
We deliver detailed written quotes that break down every material and labor cost -- no surprise line items appear on your final invoice that were not on the original estimate.
Hydrostatic pressure is the invisible force behind nearly every basement water problem homeowners face in Chester, NY. When soil around your foundation becomes saturated -- whether from heavy rain, snowmelt, or a high water table -- it exerts outward and downward pressure against concrete walls and floor slabs that can exceed hundreds of pounds per square foot. Over time, this pressure finds the smallest weakness: a tie rod hole, a cold joint between wall and footing, a shrinkage crack in poured concrete, or a deteriorated mortar joint in block construction. Once water finds its path, that path widens with every wet season until a trickle becomes a flood.
A well-installed interior drain tile system is designed around the specific hydrology of your property. Basements in Chester that sit in naturally high water table zones require larger-diameter pipe and higher-capacity pumps than basements that only collect surface runoff during heavy storms. Our assessment process measures both the volume and the frequency of water intrusion to right-size every component -- from the pipe diameter to the pump horsepower and battery backup capacity.
In poured concrete walls, the most common seepage points are cold joints, tie rod holes, and form tie locations. These are concentrated, well-defined penetrations that respond well to polyurethane or epoxy injection -- a process of drilling small ports along the crack or joint, installing surface-mounted injection ports, and pumping low-viscosity resin under pressure until it fills the void completely. The cured resin is permanently flexible or rigid depending on the product chosen, creating a watertight seal that moves slightly with seasonal concrete expansion without reopening.
Floor cracks are a separate category of water entry that many homeowners underestimate. A hairline crack in a poured concrete floor can transmit significant water when the slab sits on soil with a high water table. Injection of these cracks follows the same principle as wall cracks: drill ports, install fittings, and pump polyurethane resin that expands to fill the void and bond with the surrounding concrete. In situations where the slab has heaved or settled, crack injection is supplemented with undercutting and re-pouring a portion of the slab to restore a flat, properly sealed floor surface.
A complete basement waterproofing system also requires a reliable, properly maintained sump pump installation. We specify sump pits that are large enough to accommodate both a primary pump and a battery backup pump with sufficient separation that the backup does not interfere with the primary float. Discharge lines are routed to daylight at a point that ensures water flows away from the house and cannot recirculate back to the foundation. Battery backup systems are sized to handle a sustained pumping load during a power outage -- not just a brief test cycle -- because the storm events that knock out power are precisely the events that generate the highest water volume in your basement.
Six core services covering every source of basement moisture in Chester homes.
We size every drain tile system to the specific hydrology of your basement, ensuring the pipe diameter and sump pump capacity match your worst-case water intrusion load.
Injection ports are removed after cure and the wall surface is patched flush, leaving a clean repair with no visible hardware remaining on the wall face.
Sump pits are sized to accommodate both primary and backup pumps without float interference, and discharge lines are routed to a point at least ten feet from the foundation perimeter.
The finished surface is coated with a heavy-bodied elastomeric masonry waterproofer that bridges hairline cracks and resists surface moisture transmission year-round.
Basement floor cracks that allow water infiltration from below are treated with polyurethane injection resin pumped under pressure to fill the void and bond with surrounding concrete.
Failing or undersized window well flashing and frame seals are replaced as part of every window well drainage project to address all water entry paths simultaneously.
We measure moisture levels at multiple points, probe for efflorescence sources, and map every water entry location before recommending any solution.
Our quotes include alternatives at different investment levels so you can choose a phased approach if budget requires it.
Our certified crew completes the installation with minimum disruption to your home, working from a phased sequence designed to protect furnishings and maintain basement access throughout.
We perform a complete post-installation inspection, take final moisture readings, and walk you through the system before issuing your written warranty documentation.
After three failed attempts with other companies, JCB Waterproofing and Construction finally fixed our basement for good. The drain system has handled two major rainstorms with zero water in the basement.
Professional from the initial phone call to the final walkthrough. They explained every step of the process and answered every question without making me feel rushed.
I called three companies before choosing JCB Waterproofing and Construction. They were the only ones who actually measured the moisture levels and explained what was causing our specific problem before quoting a fix.
Get a written quote from certified professionals who have solved every type of basement water problem in NY.
Call +1-866-476-1348 Now